Add some helper functions for serial (UART) driver.

diff --git a/drivers/serial.c b/drivers/serial.c
index c7522f6..42212f6 100644 (file)
--- a/drivers/serial.c
+++ b/drivers/serial.c
@@ -149,6 +149,22 @@ static void uart_start_sending(uint32_t uart_num)
 }
 
 
+/****************************************************************************** */
+/*    Serial send byte - quick function with almost no tests.
+ * If the uart is not sending, the byte is placed directly in the data buffer and
+ * the call returns 0.
+ * Else, the call returns -EBUSY and nothing is sent.
+ */
+int serial_send_quickbyte(uint32_t uart_num, uint8_t data)
+{
+       struct uart_device* uart = &uarts[uart_num];
+       if (!uart->sending) {
+               uart->regs->func.buffer = data;
+               return 0;
+       } else {
+               return -EBUSY;
+       }
+}
 
 /***************************************************************************** */
 /*    Serial Write
@@ -239,7 +255,8 @@ struct uart_clk_cfg {
        uint8_t mul_val;
 };
 static struct uart_clk_cfg uart_clk_table[] = {
-       { 1152000, 2, 4, 13},
+       { 250000, 12, 0, 1},
+       { 1152000, 2, 3, 10},
        { 0, 0, 0, 0, },
 };
 
@@ -260,7 +277,7 @@ static void uart_clk_on(uint32_t uart_num, uint32_t baudrate)
        pclk = get_main_clock(); /* See above note */
        div = (pclk / (baudrate * 16));
        sys_ctrl->uart_clk_div[uart_num] = 0x01;
-       /* The easy one : divider is an integer, or baudrate is low enought for the aproximation */
+       /* The easy one : divider is an integer, or baudrate is low enough for the aproximation */
        if ((baudrate <= 115200) || ((div * baudrate * 16) == pclk)) {
                uart->line_ctrl |= LPC_UART_ENABLE_DLAB;
                uart->ctrl.divisor_latch_lsb = (div & 0xff);
@@ -300,7 +317,7 @@ static uint32_t uart_setup(uint32_t uart_num)
        struct lpc_uart* uart = uarts[uart_num].regs; /* Get the right registers */
        uint32_t status = 0;
        /* Set up UART mode */
-       uart->line_ctrl = uarts[uart_num].config;;
+       uart->line_ctrl = uarts[uart_num].config;
        /* Clear all fifo, reset and enable them */
        /* Note : fifo trigger level is one bit */
        uart->ctrl.fifo_ctrl = (LPC_UART_FIFO_EN | LPC_UART_TX_CLR | LPC_UART_RX_CLR);
@@ -312,6 +329,21 @@ static uint32_t uart_setup(uint32_t uart_num)
        return status;
 }
 
+/* Change UART configuration (number of data, parity and stop bits).
+ * config is a mask of LPC_UART_xBIT (x = 5..8), LPC_UART_xSTOP (x = 1..2)
+ *   and one of LPC_UART_NO_PAR, LPC_UART_ODD_PAR or LPC_UART_EVEN_PAR.
+ */
+int uart_set_config(uint8_t uart_num, uint8_t config)
+{
+       struct uart_device* uart = NULL;
+
+       if (uart_num >= NUM_UARTS)
+               return -EINVAL;
+       uart = &uarts[uart_num];
+       uart->config = config;
+       return 0;
+}
+
 struct uart_def
 {
        uint32_t irq;

diff --git a/include/drivers/serial.h b/include/drivers/serial.h
index 7f0bce8..8a6fcd8 100644 (file)
--- a/include/drivers/serial.h
+++ b/include/drivers/serial.h
@@ -77,11 +77,25 @@ int serial_write(uint32_t uart_num, const char *buf, uint32_t length);
 int serial_flush(uint32_t uart_num);
 
 
+/****************************************************************************** */
+/*    Serial send byte - quick function with almost no tests.
+ * If the uart is not sending, the byte is placed directly in the data buffer and
+ * the call returns 0.
+ * Else, the call returns -EBUSY and nothing is sent.
+ */
+int serial_send_quickbyte(uint32_t uart_num, uint8_t data);
 
 
 /***************************************************************************** */
 /*   Public access to UART setup   */
 
+
+/* Change UART configuration (number of data, parity and stop bits).
+ * config is a mask of LPC_UART_xBIT (x = 5..8), LPC_UART_xSTOP (x = 1..2)
+ *   and one of LPC_UART_NO_PAR, LPC_UART_ODD_PAR or LPC_UART_EVEN_PAR.
+ */
+int uart_set_config(uint8_t uart_num, uint8_t config);
+
 /* Change uart mode to RS485
  * return -ENODEV when the device does not support RS485 mode.
  */